If you wish to start mining, you can check out these options: GPU Pool Mining is recommended as it has the highest success rate. As a result, pool diversity is very important and people should try to find the best pool or independent ones, to solidify the network. If a pool dominates (controls at least 51% of all the mining power), it means that they have full control over the blockchain and can therefore cheat the system by modifying some of the values (essentially creating, stealing, or removing money). Some pools might also have a pooling fee, which are usually used by the owner to pay for their pool's hosting cost. Because pools are groups of miners, when they reach a reward, it is distributed to everybody based on how much they contributed (meaning a much lower reward than with solo mining). Mining monitoring and management software for your Windows GPU rigs. This group is able to mine much more efficiently, which might lead to a higher success rate (and therefore reward) to its miners. View Garlicoin (Allium) mining pools, their fees, payout threshold, and reward methods. Pool mining is when multiple miners get together and mine as a group (called a pool). Solo mining is when a miner tries to mine by themselves this can lead to a much higher block reward than pool mining (because the reward isn't shared), but is much more difficult because others might be able to mine faster and the Solo miner will never be able to mine one before everyone else. When mining, whoever succesfully verifies (or mines) a block first gets the reward for mining it. It should be noted that mining on a laptop is not recommended (although feasible), because laptops are much less powerful and could get damaged much more easily. Mining on the CPU is more accessible and easier to setup, but mining on the GPU is much faster and will yield to better results It is therefore recommended to mine on the GPU (if available). Miners can use either their CPU (processor) or GPU (graphics card) to mine Garlicoin (since Garlicoin is ASIC resistant, those are the only two options). Miners can only use their CPU (Processor) and GPU (Graphics Card) to mine Garlicoin as it is ASIC resistant meaning that it will try to block mining on mining-specific hardware. You can learn more about how blockchain works here. For each verification a miner makes, they get a small amount of newly created Garlicoin for their "hard" work. If you need any more help please check out the forum at fabulouspanda.Mining, in cryptocurrency, is the process of verifying that a transaction is valid using computer calculations. Where 4 is the number of threads you want to use for mining, like so: If you only want to use a portion of the available threads, use the flag -t 4 Garlicoin (GRLC) Mining Profit Calculator - WhatToMine Active (not listed) Garlicoin (GRLC) Algorithm: Allium Block time: 41s Last block: 3,969,546 Bl. If you don't know how many that is, this is a good way to find out. stratum+tcp:// at the beginning Save, and from the View menu, open the GPU and/or CPU miner windows, depending on which you want to use. Hit start on the CPU miner and it'll start mining using all available CPU threads. Then hit start on the GPU miner and you're good to go! Experiment with what works best for your card but remember that higher settings run hotter. I recommend setting Intensity to 11, running on an AMD Radeon HD 7870 going any higher than 11 causes mostly invalid shares to be submitted to the pool. You may also wish to alter your Intensity setting. For GPU mining, open that and set the manual flag -nfactor 11Īnd hit apply. Save, and from the 'View' menu, open the GPU and/or CPU miner windows, depending on which you want to use.Įach miner window has a little cog button that opens the miner settings. It is necessary to include the pool protocol for mining to work, so make sure the pool has stratum+tcp:// The MacMiner software is an easy-to-use mining software that comes with a graphical user interface, and several preinstalled console miners. Set up the pool making sure you're using Scrypt Adaptive-N, like so: In MacMiner, press cmd comma or use the menu bar to open the preferences pane from the MacMiner menu. For GPU mining, open that and set the manual flag -nfactor 11 like so: and hit apply. Each miner window has a little cog button that opens the miner settings. Once registered at the pool I create a worker on the website, which gives me a username and a worker name, and I just use x for the password as it is not required at this pool. stratum+tcp:// at the beginning Save, and from the 'View' menu, open the GPU and/or CPU miner windows, depending on which you want to use. For the purposes of this tutorial, I'll be using Next, find a Scrypt Adaptive-N pool you want to mine at.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |